MilitaryStockholm

Announcement

Collapse
No announcement yet.

The Bundeswehr M1 Helmet

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    The Bundeswehr M1 Helmet

    Hello fellow collectors,

    I thought that it would be of interrest to some of you
    to show some details of the first BW helmet from 1956.

    All the information can be found in the book of Mr.Baer , but I think
    that this information is only available in german version.

    First info is that only two manufacturers were contracted for the shell.
    One of these was the well known firm Quist and the other one was
    Linnemann+Schnetzer.
    The steel that was used was of quite low quality as it was forbidden by the allies to produce the high quality steel of the WWII helmets.

    The liners were produced by five different manufacturers.

    Let us start with a very fine magazine cover from 1956 !
    Attached Files

    #2
    A closeup showing the issue helmet net , and the chinstrap.
    Attached Files

    Comment


      #3
      I have three complete helmets in my collection.
      All of them are dented as a result of the low quality steel , and
      all of them are period repainted on the outside.

      All three helmets are Quist made in 1956.
      First helmet:
      Attached Files

      Comment


        #4
        Second helmet showing another shade of repaint !
        Attached Files

        Comment


          #5
          Third , and as you can imagine, my favorite helmet
          Attached Files

          Comment


            #6
            Inner view of the helmet shell showing dents and manufacturer
            F.W.Quist 1956 and lot number 49
            Attached Files

            Comment


              #7
              Another helmet interior has this marking :
              SPZ Luthardt in german SPZ means the same as APC
              Schützenpanzer = Armoured Personnel Carrier

              This helmet is , as you can see from the 20th rate from 1956
              Attached Files

              Comment


                #8
                Now on to the liners.
                Mr.Bear writes that 5 manufacturers were contracted to make these liners.
                Among these one maker is very well known : S.W.B means
                Schuberth Werke Braunschweig.

                Here from the magazine some pics showing BW personnel wearing these
                liners.
                "Bürger in Uniform" means "Citizens in Uniform"
                Attached Files

                Comment


                  #9
                  Here is a group shot of all five liners I own.
                  All are made between 1956 and 1959.
                  Of special note is the fact that not two of them have the same colour.
                  Attached Files

                  Comment


                    #10
                    Inside look of a liner:
                    Attached Files

                    Comment


                      #11
                      Named sweatband:Gefr.Deinert
                      Attached Files

                      Comment


                        #12
                        That´s it for now , hope you like it !!
                        Regards

                        Bernhard

                        Comment


                          #13
                          Bernhard,

                          Nice thread and a good addition to the West German helmet thread that we had running a few weeks ago. If memory serves me correctly, Baer says that the first issue of BW helmets were purchased from Belgium and would therefore have had Belgian liners. Do you have any of these helmets in your collection?

                          Regards,

                          Gordon

                          Comment


                            #14
                            Bravo Bernhard!

                            Excellent photos of this very hard to find combination!

                            It was also interesting to note that the Bundeswehr made limited use of Bundesgrenzschutz leather gear for use with the G-1 rifle.

                            We have always wondered about the function of the "d" ring tab over the pockets of the Model 1955 Battle Dress. In the picture in post one, it appears as though the soldier is using it to tie off a lanyard of some kind, perhaps to a compass or code book.

                            In any event, great pictures, thanks for sharing.

                            TJ

                            Comment


                              #15
                              Gordon ,TJ

                              Thank you both for your comments.
                              I reread the chapter on the first BW helmet in the Bear book , but I only
                              can say that the government planned to invent the US/Begium helmet
                              model.
                              Baer does not state that the germans have actually bought helmets from
                              Belgium.
                              Strange for me is one statement about the german helmet industry :
                              Mr Bear writes that "....after producing the two piece helmet for France
                              and the US , the german industry was well prepared for the production of
                              the own BW helmet ".....
                              Never knew that there was a german production US M1 helmet ??

                              Regards

                              Bernhard

                              Comment

                              Users Viewing this Thread

                              Collapse

                              There is currently 1 user online. 0 members and 1 guests.

                              Most users ever online was 4,375 at 10:03 PM on 01-16-2020.

                              Working...
                              X